MaxTech Plug & Play Internal Voice/FAX/Data/SVD Modem Manual de usuario Pagina 1

Part #MAN128 Rev. 1.0 K56Plus-L/CPI-SVDHigh PerformanceK56Plus/V.34+/V.42bis56K BPSPlug & Play InternalVoice/FAX/Data/SVDModemWith AdvancedSpeaker

8B1 Bell modeB2 V.23 originate mode @ 75 bps transmit/1200 bps receiveB3 V.23 originate mode @ 1200 bpstransmit/75 bps receiveB15 Selects V.21 at 300

9O_ O0 Return to Data ModeO1 Return to Data Mode and initiate anequalizer retrainP Set Pulse dial as defaultQ_ Q0 Modem sends responsesQ1 Modem does n

10DTR toggle&D2 Modem hangs up, returns to theCommand Mode after DTR toggle&D3 Resets modem after DTR toggle&F_ &F Recall factory defa

11compression%C1 Enable MNP Class 5 data compressiononly&Q_ &Q0 Direct data link only (same as \N1)&Q5 V.42 data link with fallback option

12pass XON/XOFF to remote modem orlocal DTE-C_ -C0 Data calling tone disabled-C1 Data calling tone enabled3.6 Fax Class 1 Commands+FCLASS? Service cla

13+FDTC: Report the polled station capabilities+FET: Post Page Message Response+FET=n Transmit Page Punctuation+FHNG Call Terminations with Status+FK

14-SRM Retrieve message-SSE=n n=0 Disable DSVDn=1 Enable DSVD-SSP Set transmission speeds-SSR Start sequence response control-SSV Data mode event mess

15S37 Connection speed 0-19 0S38 56K dial line rate 0-16 1S42-43 ReservedS48 LAPM negotiation 7, 128 7S89 Sleep mode timer 0, 5-255 seconds 10S90 Loca

16to “talk” to the modem on the correct COM port and IRQ setting (same COM port and IRQ setting as the modem). Your communication software must know w

17COM ports:1, 2, 3, 4IRQ lines: 3, 4, 5, 7, 9, 10, 11, 12, 15FAX Group: Group III Send/ReceiveStandardFAX Command set: EIA/TIA-578 Service Class 1,EI

The information contained in this manual has beenvalidated at the time of this manual's production.The manufacturer reserves the right to make an

18The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)).FCC Class B Statemen

19NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is

20

21

1Section One - IntroductionThis 56 Kbps* Plug and Play FAX/Voice/Data/SVD Speakerphone Modem connects your computerto all popular high speed modems av

2(e.g., Windows 95),orB) A Plug and Play Revision 1.0a compliant PC.Proceed to Section 2.3 now if you have every-thing required.If you have neither 2A

37. Connect the telephone cable from the modem'sLINE connector to the telephone wall jack.8. Optionally, connect your telephone to the modem&apos

42.4.1.1 Windows 95 Release 4.00.950When Windows 95 starts for the first time aftercard installation, it detects the modem and displays theNew Hardwar

52.4.2 Configuring in a Plug and Play System with-out Windows 95When this modem is installed in a Plug and Playsystem without Windows 95, the computer

6RJ-11 jack marked “PHONE” or by attaching a micro-phone to the MIC jack and a speaker to the SPK jackof your sound card. Follow instructions in the F

7are interested in accessing the modem manually, andnot through the included software. Section 4 and 5contain reference material, and can be skipped.