MaxTech NXP-16 Especificaciones Pagina 53

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 75
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 52
LEON-G100/G200 - System Integration Manual
GSM.G1-HW-09002-C Preliminary Design-In
Page 53 of 75
Rank
Function
Pin(s)
Layout
Remarks
1
st
RF Antenna In/out
Very
Important
Design for 50 characteristic impedance.
See section 2.2.1.1
2
nd
DC Supply
Very
Important
VCC line should be wide and short. Route away
from sensitive analog signals. See section 2.2.1.2
3
rd
Analog Audio
Careful Layout
Avoid coupling with noisy signals
See section 2.2.1.3
Audio Inputs
MIC_BIAS1, MIC_GND1,
MIC_BIAS2, MIC_GND2
Audio Outputs
SPK_P, SPK_N, HS_P
4
th
Ground
GND
Careful Layout
Provide proper grounding.
See section 2.2.1.4
5
th
Charger
V_CHARGE,
CHARGE_SENSE
Careful Layout
Check Charger line width.
See section 2.2.1.5
6
th
Sensitive Pin :
Careful Layout
Avoid coupling with noisy signals.
See section 2.2.1.6
Backup Voltage
V_BCKP
A to D Converter
(If implemented)
ADC1
Power On
PWR_ON
7
th
Digital pins :
Common
Practice
Follow common practice rules for digital pin
routing
See section 2.2.1.7
SIM Card Interface
VSIM, SIM_CLK, SIM_IO,
SIM_RST
Digital Audio
I2S_CLK, I2S_RXD,
I2S_TXD, I2S_WA
DDC
SCL, SDA
UART
TXD, RXD, CTS, RTS, DSR,
RI, DCD, DTR
External Reset
RESET_N
General Purpose I/O
GPIO1, GPIO2
Table 8: Pin list in order of decreasing importance for layout design
2.2.1.1 RF Antenna connection
The RF antenna connection pin ANT is very critical in layout design. The PCB line must be designed to provide 50
characteristic impedance and minimum loss up to radiating element.
Provide proper transition between the ANT pad to application board PCB
Increase GND keep-out for ANT pin to at least 250 µm up to adjacent pads metal definition and up to 500
µm on the area below the Data Module
Add GND keep-out on buried metal layers below antenna pad if top-layer to buried layer dielectric thickness
is below 200 µm
The transmission line up to antenna connector or pad may be a micro strip or a stripline. In any case must be
designed to achieve 50 characteristic impedance;
Microstrip lines are usually easier to implement and the reduced number of layer transitions up to antenna
connector simplifies the design and diminishes reflection losses. However, the electromagnetic field extends
to the free air interface above the stripline and may interact with other circuitry
Buried stripline exhibits better shielding to incoming and generated interferences. Therefore are preferred for
sensitive application. In case a stripline is implemented, carefully check that the via pad-stack does not
couple with other signals on the crossed and adjacent layers
Minimize the transmission line length; the insertion loss should be minimized as much as possible, in the
order of a few tenths of a dB
The transmission line should not have abrupt change to thickness and spacing to GND, but must be uniform
and routed as smoothly as possible
ANT
VCC
Vista de pagina 52
1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 74 75

Comentarios a estos manuales

Sin comentarios

Prime-Line N 6603 manuály

Uživatelské manuály a uživatelské příručky pro ne Prime-Line N 6603.
Poskytujeme 1 manuály pdf Prime-Line N 6603 ke stažení zdarma podle typů dokumentů: Manuál s instrukcemi


Prime line N 6603 Manuál s instrukcemi (1 strany)


Značka: Prime-line | Kategorie: No info | Velikost: 0.09 MB |

  

Tabulka s obsahem





Další produkty a příručky pro ne Prime-Line

Modely Typ Dokumentu
K 5145 Manuál s instrukcemi     Prime-Line K 5145 Instructions / Assembly, 1 stránky
RZ 50-4A24 Instalační příručka    Prime-Line RZ 50-4A24 Installation Guide, 1 stránky
U 9845 Manuál s instrukcemi    Prime-Line U 9845 Instructions / Assembly, 1 stránky
U 9862 Manuál s instrukcemi    Prime-Line U 9862 Instructions / Assembly, 1 stránky
U 9868 Manuál s instrukcemi    Prime-Line U 9868 Instructions / Assembly, 1 stránky
E 2054 Manuál s instrukcemi    Prime-Line E 2054 Instructions / Assembly, 1 stránky
U 9911 Manuál s instrukcemi     Prime-Line U 9911 Instructions / Assembly, 1 stránky
F 2509 Manuál s instrukcemi    Prime-Line F 2509 Instructions / Assembly, 1 stránky
D 1558 Manuál s instrukcemi    Prime-Line D 1558 Instructions / Assembly, 1 stránky
E 2320 Instalační příručka    Prime-Line E 2320 Installation Guide, 1 stránky
B 503 Manuál s instrukcemi    Prime-Line B 503 Instructions / Assembly, 1 stránky
TH 23057 Manuál s instrukcemi     Prime-Line TH 23057 Instructions / Assembly, 1 stránky
D 1559 Manuál s instrukcemi    Prime-Line D 1559 Instructions / Assembly, 1 stránky
N 6640 Manuál s instrukcemi    Prime-Line N 6640 Instructions / Assembly, 1 stránky
B 668 Manuál s instrukcemi    Prime-Line B 668 Instructions / Assembly, 1 stránky
N 6555 Manuál s instrukcemi    Prime-Line N 6555 Instructions / Assembly, 1 stránky
F 2644 Manuál s instrukcemi    Prime-Line F 2644 Instructions / Assembly, 1 stránky
B 544 Manuál s instrukcemi    Prime-Line B 544 Instructions / Assembly, 1 stránky
M 6192 Manuál s instrukcemi    Prime-Line M 6192 Instructions / Assembly, 1 stránky
H 3552 Manuál s instrukcemi    Prime-Line H 3552 Instructions / Assembly, 1 stránky